Screen Guard for Redmi Watch Move 1.85" Watch - Pack of 2 TPU Screen Protector Film - Not a Tempered Glass, No Chipped Edges, Self Repairing Surface, 9H Hardness, Anti Glare Free Touch
6 sold in last 24 hours
- NOT A TEMPERED GLASS - AND THAT IS THE POINT: on a square display glass chips at the corners and lifts where the display curves. This TPU film, cut for Redmi Watch Move 1.85", bends with the watch and stays down.
- NO SHARP CHIPPED EDGES: a cracked watch glass leaves a sharp rim right against your wrist. Film cannot shatter, splinter or flake, so a hard knock ends with a mark on the protector and nothing else.
- SELF REPAIRING SURFACE: micro scratches disappear as the polymer relaxes back into shape - something no tempered glass can do. Your screen keeps a clean, unscratched face for far longer.
- FULL CURVE COVERAGE: because it flexes, the film reaches the rolled edge of the display where flat glass leaves a white halo or peels away within a week.
- WHAT YOU GET: 2 protectors, prep wipe, dust sticker and microfibre cloth. Wet or dry application, repositionable while you line it up, bubble free once it settles.
Estimated shipping
Select a product to estimate shipping.A film that takes the damage so the watch does not
A smartwatch display picks up its first scratch long before anything else on the watch shows wear, and once it is there you cannot polish it out. This is the layer that takes it instead. A flexible 9H TPU film — not a tempered glass — so it follows the curve of a square display right to the rim, absorbs a knock rather than cracking, and closes over light scratches on its own within about a day. At 0.15 mm it disappears in use: full touch response, true colour, nothing for a shirt cuff to catch on. Two protectors and a complete fitting kit in every pack.
Rigid glass was designed for flat phone screens
A watch display curves at the edge, and that is precisely where tempered glass fails. It either stops short of the curve and leaves the rim bare, or it lifts within a few weeks and shows a white halo around the edge. When it finally breaks, it leaves a chipped rim sitting against your wrist. A flexible TPU protector bends with the square display, holds its grip at the edge, cannot shatter or splinter, and repairs the light scratches that glass keeps for good. The 9H hard coat gives you the scratch resistance people buy glass for in the first place.
9H scratch resistant
True colour, no rainbow sheen
Touch, exactly as it was
Covered to the last millimetre
The only protector that undoes its own damage
The top layer is elastic. When something fine drags across it — a fingernail, a zip, a grain of sand — the polymer deforms rather than tearing, and then relaxes back into shape. Light scratches close over on their own, usually inside 24 hours, faster in warm weather. It is why a film that has been on a wrist for six months still looks clean, while a tempered glass slowly collects a haze of hairlines that never leave. Deep gouges will not disappear, but almost nothing a watch meets in normal use is deep.
Hard on the outside, soft where it matters
The top layer is a 9H hard coat and takes the scratches. The middle is a shock absorbing core that spreads the force of a knock across the whole film instead of letting it land on one point of the display, and it is the layer that closes light scratches on its own. The base is a silicone adhesive that grips without trapping air, so it goes on bubble free and peels away clean with no residue. All of it together measures 0.15 mm — which is why the watch still feels bare under your finger and the film disappears the moment it is on.
Sweat, rain and shower safe
Fingerprints wipe straight off
No gap for dust to sit in
1. Clean the display
Wipe the screen with the alcohol pad in the box, then lift the last specks with the dust sticker. A clean surface is the whole secret to a bubble free finish.
2. Peel and align
Peel the backing tab and lower the protector over the square display. It stays repositionable while you line it up, so take your time getting it square to the bezel.
3. Press from the centre
Press down in the middle and work outwards. Any small bubbles at the edge pull themselves out over the next few hours as the film settles.
Product details
| Main Specification | |
|---|---|
| Included Components | Dry Wipe or Screen protector or Wet Wipe or Dust Absorber Sticker |
| Special Feature | Scratch Resistant or 9 H Surface Hardness or Anti-Fingerprint or High Definition Clarity or Anti-Bubble |
| Manufacturer | HELLOSCREEN |
| Unit Count | 2.0 Count |
| Brand | HELLOSCREEN |
| Compatible Phone Models | Redmi Watch Move 1.85" |
| Number of Items | 2 |
| Model Name | HELLOSCREEN Smartwatch Screen Protector 1.85 Inch |
| Product Dimensions | 5L x 4W Centimeters |
| Compatible Devices | For Redmi Watch Move |
| Material | Thermoplastic Polyurethane |
| Colour | Transparent |
| Finish Type | Glossy |
| Screen Surface Description | Glossy |
| Item Weight | 10 Grams |
| Product information | |
| Screen Size | 1.85 inches |
| Technical Details | |
| Special Features | Scratch Resistant or Anti-Fingerprint or High Definition Clarity or 9 H Surface Hardness or Anti-Bubble |
| Part Number | HSSW134V3 |
| Material Type | Thermoplastic Polyurethane |
| Item Hardness | 9H |
| Country of Origin | India |
| Item details | |
| Model Number | For Redmi Watch Move |
| Item Type Name | Screen Protector |
| Others | |
| Product Type | Screen Protector |
| Packer Contact Information | HELLOSCREEN |
| Item Dimensions L x W | 5L x 4W Centimeters |
| Net Quantity | 2.0 Count |
| Display Size | 1.85 Inches |
| Clarity | 99.9 |